
Energy Savings in Injection Molding – Kutting WFI Hoses
Energy Savings in Injection Molding: 42% Shorter Mold Heat-Up Time with Kutting WFI Insulated Hoses
An industrial study conducted by RK Kutting and EJOT demonstrates how properly selected temperature-control hoses and effective thermal insulation can improve energy efficiency, production availability, and workplace safety in plastic injection molding applications.
The Importance of Energy Efficiency in Plastic Injection Molding
When discussing energy efficiency in plastic injection molding, attention usually focuses on the injection molding machine itself, heating elements, mold temperature controllers, and cooling systems.
However, one potential source of energy loss is often overlooked: the hoses connecting the mold to the temperature-control units.
Particularly when processing engineering and high-performance thermoplastics that require elevated mold temperatures, heat is continuously released into the surrounding environment through hoses and their connections.
These thermal losses can increase energy consumption, extend mold heat-up times, raise ambient temperatures in production areas, and create burn hazards for machine operators.
To investigate this issue, Germany-based RK Kutting and EJOT conducted a joint industrial study examining the performance of thermally insulated hose systems under actual production conditions.
The findings, published in Kunststoffe International in September 2020, demonstrate the potential benefits of optimizing hose systems in injection molding operations.
A Study Conducted Under Real Production Conditions
The research was carried out on an injection molding machine operating in series production at EJOT.
The main application parameters were:
Injection molding machine with a clamping force of 1,400 kN
Two-cavity mold with sliding elements and an integrated hot runner system
Automotive cooling-system pump housing manufactured from polyphenylene sulfide (PPS)
Mold operating temperature of 160°C
Seven temperature-control circuits
Four mold temperature controllers
Three-shift production operation
The original installation used approximately 62.6 meters of conventional Kutting WF corrugated hoses with stainless-steel outer braiding.
As part of the optimization project, the existing hose system was replaced with Kutting WFI flexible corrugated hoses featuring integrated multi-layer thermal insulation.
However, the project involved more than simply replacing the hoses.
Hose lengths were optimized, metallic fittings were insulated, hose routing was reorganized, and thermal bridges were reduced to improve overall system efficiency.
Reducing Heat Loss with Kutting WFI Insulated Hoses
Kutting WFI hoses combine flexible corrugated metal hose construction with integrated multi-layer thermal insulation.
This design helps reduce heat transfer from the temperature-control medium to the surrounding environment.
The main advantages of Kutting WFI hose systems include:
Integrated thermal insulation that reduces the need for additional external insulation
Lower hose surface temperatures
Reduced heat losses and improved energy efficiency
Flexible construction for easier machine installation
Durability suitable for demanding applications involving moving mold components
Silicone-free design
Reduced risk of contact burns for machine operators
These characteristics are particularly valuable in injection molding processes involving elevated mold temperatures and continuous production.
By minimizing unnecessary heat dissipation, insulated hoses can help maintain a more efficient and safer temperature-control system.
42% Reduction in Mold Heat-Up Time
One of the most significant findings of the study was the reduction in the time required for the mold to reach its operating temperature.
Following the installation of Kutting WFI hoses and the implementation of additional insulation measures, mold heat-up time was reduced by 60 minutes, representing an improvement of 42%.
This result is particularly important for applications where molds must be cooled and subsequently reheated during maintenance, cleaning, or production interruptions.
Shorter heat-up times allow injection molding machines to return to production more quickly, potentially increasing machine availability and reducing downtime-related costs.
For manufacturers operating high-value injection molding equipment, improvements in machine availability can provide substantial operational benefits.
Measured Energy Savings of 3.4 kW During Production
During the initial project assessment, the combined optimization measures were estimated to offer approximately 6.5 kW of potential energy savings.
This theoretical estimate included improvements from:
Integrated hose insulation
Shorter hose lengths
Insulated hose fittings
Optimized hose routing and reduced thermal bridges
However, measurements conducted under actual operating conditions demonstrated energy savings of 3.4 kW during ongoing production.
The difference between the theoretical estimate and the measured result highlights the importance of evaluating energy efficiency across the entire injection molding process.
When heat losses are reduced, not all retained energy necessarily translates directly into lower energy consumption.
Some of the additional available energy may contribute to the thermal balance and temperature distribution within the mold.
Nevertheless, the measured reduction confirms that proper hose selection and thermal insulation can make a meaningful contribution to energy efficiency.
Hose Surface Temperature Reduced by 51°C
In addition to reducing energy consumption, the optimization project delivered important occupational safety benefits.
Before the modifications, conventional non-insulated hoses reached very high surface temperatures, creating potential burn hazards for operators working around the machine.
Following the installation of the Kutting WFI hose system and insulated fittings, a reduction of 51°C in hose surface temperature was measured.
This improvement provided several benefits:
Reduced risk of accidental contact burns
Lower heat emission into the production environment
Improved thermal comfort for machine operators
Potential reduction in the cooling demand of the production facility
For injection molding companies operating at high process temperatures, these improvements can contribute to both workplace safety and a more comfortable production environment.
Investment Payback and Economic Benefits
The economic assessment demonstrated that the combination of energy savings and reduced mold heat-up time can generate significant operational benefits.
In the evaluated application, the economic value of the production time saved during reheating after cleaning and maintenance was sufficient to support an investment payback period of less than one year.
Additional benefits were associated with reduced energy consumption and lower heat emissions into the production environment.
The study also identified potential advantages related to production-area cooling requirements, although these were not quantitatively evaluated.
Actual savings and payback periods depend on several application-specific factors, including:
Mold operating temperature
Total installed hose length
Operating hours and production schedules
Temperature-control system configuration
Energy costs
Frequency of mold cleaning and maintenance
Existing hose insulation and connection design
Therefore, each application should be evaluated individually to determine its potential for optimization.
Polmak Plastik and Kutting: Efficient Temperature-Control Solutions
As the representative of Kutting in Türkiye, Polmak Plastik provides industrial hose and connection solutions for the plastics processing industry.
Kutting WF and WFI hose systems can be considered for plastic injection molding machines, mold temperature-control equipment, and other suitable industrial applications involving temperature-controlled fluids.
Selecting the appropriate hose system requires more than determining the nominal diameter and fitting dimensions.
Important technical considerations include operating temperature, pressure, fluid compatibility, mechanical movement, installation conditions, connection reliability, and potential thermal losses.
At Polmak Plastik, our objective is not only to supply suitable industrial components but also to support our customers in developing safer, more efficient, and more sustainable production processes.
For technical information about Kutting WF and WFI hoses, or assistance in selecting the appropriate solution for your application, please contact Polmak Plastik.
Source: Mark Berlin, Less Is Often More - Potential Savings Arising from the Use of Energy Management in Mold Temperature Control, Kunststoffe International, September 2020. Industrial application study conducted by RK Kutting and EJOT.
Note: All performance figures refer to the specific industrial application described in the study. Actual results may vary depending on operating conditions and system configuration.
NEWS ARCHIVE